Page 7 of 7 FirstFirst 1234567
Results 151 to 164 of 164
  1. #151
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    Promaster RV Build-pm-116-jpg

    Another fix I did was the vent for the chest fridge, I tried to find a grille to cover it but because the opening is higher than wide I couldn't find one that looked good.

    Promaster RV Build-pm-165-jpg

    So instead of a grille I carpeted the wood and insulation, the boss said it looks OK that's good enough for me.
    Attached Thumbnails Attached Thumbnails Promaster RV Build-pm-116-jpg   Promaster RV Build-pm-165-jpg  

  2. #152
    Days Work Done! Norton's Avatar
    Join Date
    Oct 2007
    Last Online
    @
    Location
    Roiet
    Posts
    30,940
    Damn Dennis, getting everything to fit and function is a blivet.

    https://www.urbandictionary.com/define.php?term=blivet

  3. #153
    Member
    Join Date
    Jul 2007
    Last Online
    @
    Posts
    492
    Quote Originally Posted by Chittychangchang View Post
    I spotted this bad boy today, only 30k!
    What year was that Chitty?
    Maybe I should have held on to the 1969 similar bus /camper that put me back 12K DM.

  4. #154
    I'm in Jail

    Join Date
    Jan 2010
    Last Online
    Today @ 09:06 PM
    Location
    TD has gone to the Dogs
    Posts
    10,475
    Dennis you need a charge controller i think - i'm no expert though

    https://www.mastervolt.com/products/alternators-charge-regulators/

  5. #155
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    Quote Originally Posted by NamPikToot View Post
    Dennis you need a charge controller i think - i'm no expert though

    https://www.mastervolt.com/products/alternators-charge-regulators/
    Thanks NPT,
    I read the specs on it, and it may work but I don't want to spend close to 300 to find out, I think what I've wired up now should work but I'll have to have someone monitor the wires while I'm driving to make sure they don't get too hot, the other option would be to increase my wire gauge to prevent the wires from heating up.

  6. #156
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    Quote Originally Posted by Norton View Post
    Damn Dennis, getting everything to fit and function is a blivet.

    https://www.urbandictionary.com/define.php?term=blivet
    Hi Norton, you got that right but I like a challenge, as long as I can find a solution, sometimes it can get to be a real head scratcher

  7. #157
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    I finally remember to take those pictures of the awning out.

    Promaster RV Build-pm-168-jpg

    Don't know if it would really need outer supports but I feel safer with them there just in case the wind would come up.

    Promaster RV Build-pm-169-jpg

    The pole is emt conduit cut to length and a 10 lb weights that were collecting dust re-purposed, I put a 1/2" bolt through the weight bolted it tight and drilled a hole in it so I could pin the conduit to it. Easy to assemble and disassemble.

    Promaster RV Build-pm-170-jpg

    The top is locked to the channel with a toilet tee bolt threaded into a dowel driven and epoxied into the conduit, the round piece is a piece of plywood with a furniture nut in it that tightens the tee bolt to the channel.

    Promaster RV Build-pm-171-jpg

    Closeup of the upper part that locks into the channel.

    Promaster RV Build-pm-172-jpg

    Finding a place to store the poles took a little thinking, what I did was cut and mount a piece of pvc conduit through the wall of the coat closet, that makes it easy to slide them in and keep them in place.
    Attached Thumbnails Attached Thumbnails Promaster RV Build-pm-168-jpg   Promaster RV Build-pm-169-jpg   Promaster RV Build-pm-170-jpg   Promaster RV Build-pm-171-jpg   Promaster RV Build-pm-172-jpg  


  8. #158
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    The one pole on the left is a couple inches shorter than the right, idea was that water would go to that corner, but it didn't seem to do that, with the rain we had this last weekend out, water ran off along the whole end.

  9. #159
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    Update, charging from van alternator is working, the wires get warm but not hot. The big relay on the left handles the charging current, the left charge controller only operates the relay coil, I do need to manually start the relay with the small micro switch which is located between relay and charge controller, when battery is fully charged everything shuts off. By charging from the alternator it is very fast, I only drove about 30 - 45 minutes from the time I started charging until we got home, it wasn't completely charged so I started battery charger and within a hour it had shut off, battery fully charged. With out using the alternator before it would take up to 12 hour to charge with 8 amp charger.


    Promaster RV Build-pm-174-jpg
    Attached Thumbnails Attached Thumbnails Promaster RV Build-pm-174-jpg  

  10. #160
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    If you look at the above photo you can also see that I got rid of the cheap ebay ground strip and installed a good ground strip that I salvaged out of an old electrical box.

  11. #161
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    Added a shelf under the bed for bag chairs and Thai front door mat and whatever else I can fit, cleans up some floor space for bigger things.

    Promaster RV Build-pm-175-jpg
    Attached Thumbnails Attached Thumbnails Promaster RV Build-pm-175-jpg  

  12. #162
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    Fixed problem with cabinet door opening every time we closed sliding door, the 2 magnetic latches weren't strong enough to hold it shut.

    Promaster RV Build-pm-176-jpg

    It's a (push to latch) latch

    Promaster RV Build-pm-177-jpg

    Latch in open position.

    Promaster RV Build-pm-178-jpg

    Latch in locked position.
    Attached Thumbnails Attached Thumbnails Promaster RV Build-pm-176-jpg   Promaster RV Build-pm-177-jpg   Promaster RV Build-pm-178-jpg  

  13. #163
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    Fixed another problem, whenever it rained water would drip on the counter and floor if we opened the sliding door. This is the material I used, E600 adhesive and 3/4" clear plastic wall corner protector.

    Promaster RV Build-pm-179-jpg

    The E6000 take 72 hours to cure so I had to tape it to keep it in place.

    Promaster RV Build-pm-180-jpg

    Finished product, hard to see what I did.

    Promaster RV Build-pm-182-jpg

    Promaster RV Build-pm-183-jpgI left a 3/16" gap to catch any rain water.
    Attached Thumbnails Attached Thumbnails Promaster RV Build-pm-179-jpg   Promaster RV Build-pm-180-jpg   Promaster RV Build-pm-181-jpg   Promaster RV Build-pm-182-jpg   Promaster RV Build-pm-183-jpg  

    Last edited by dennis4558; 24-08-2019 at 07:15 AM.

  14. #164
    Member

    Join Date
    Jan 2012
    Last Online
    19-05-2020 @ 06:49 AM
    Posts
    589
    The of the things I still needed to do was find a spare tire, none provided when I bought the van. I'd been searching for a rim for some time now, nothing local, online price was $85, I recently found one on line for $65 including shipping so I jumped on it.

    Promaster RV Build-pm-186-jpg

    Went to a friends house who has a manual tire changer and mounted it, he also has a bubble balancer so got it balanced also.

    Promaster RV Build-pm-185-jpg

    Found a tire at a local auto wrecking yard for $25, has a few very small weather checks but for a spare it will do fine.

    Promaster RV Build-pm-187-jpg

    Tire mounted and balanced ready to be mounted under van.

    Promaster RV Build-pm-188-jpg

    Mechanism and tools required to lower and raise tire under rear of van.

    Promaster RV Build-pm-189-jpg

    Tire raised and secured under van.
    Attached Thumbnails Attached Thumbnails Promaster RV Build-pm-186-jpg   Promaster RV Build-pm-185-jpg   Promaster RV Build-pm-187-jpg   Promaster RV Build-pm-188-jpg   Promaster RV Build-pm-189-jpg  


Page 7 of 7 FirstFirst 1234567

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •